Where is the sv650 tool kit




















Email to friends Share on Facebook - opens in a new window or tab Share on Twitter - opens in a new window or tab Share on Pinterest - opens in a new window or tab. Add to Watchlist. People who viewed this item also viewed. Showing Slide 1 of 1. Picture Information. Mouse over to Zoom - Click to enlarge. Have one to sell? Sell now - Have one to sell? Shop with confidence. Get the item you ordered or get your money back.

Learn more - eBay Money Back Guarantee - opens in a new window or tab. Seller information pisa Contact seller. Visit store. See other items More See all. Details about Suzuki SV Toolkit. Item Information Condition:. GBP Sign in to check out Check out as guest. The item you've selected was not added to your cart.

Add to Watchlist Unwatch. Watch list is full. This amount is subject to change until you make payment. For additional information, see the Global Shipping Program terms and conditions - opens in a new window or tab.

Accepts Offers. Buy it now. Item location. Ireland Only. European Union. Continental Europe. Delivery options. Free international postage. Collection in person. Free collection in person. Show only. Returns accepted. Authorised seller. Completed items. Sold items. More filters All listings Accepts Offers Auction Buy it now. Clamps over housing and cable allowing an aerosol can with nozzle to be connected. Once the lubrication solution runs out the far end, the cable is lubricated.

Designed to seal completely around the cable housing and stop all those messy leaks. With the unit closed and sealed around the cable, your cable gets better lubrication and you waste less lubricant. Includes degree wheel, dial-gauge, multi-position stand, extension, 3-sizes of positive-piston stops, and a handsome wooden carrying case. A handy pocket size slide calculator from Mikuni to help you calculate jetting changes due to temperature and elevation changes.

Will work for single and multiple cylinder machines whether 2 or 4 stroke. Also includes a guide for determining rich or lean conditions. Designed for quick and accurate alignment, this tool clamps squarely to the rear sprocket so the alignment rod can indicate sprocket alignment with the chain.

Here is a tool to help you remove a few links from a chain that is too long. A great tool to have in your tool box. The head of the pivot pin you are going to remove must be ground down level with the side plate before using this tool to push it out. Failure to do that will cause damage to the tool that is not covered by any warranty!

This brush has 2. It will help the performance and life of the chain, sprockets, and the engine. This brush will fit any or series chains.

Innovative design that cleans chain from 3 angles at once. Long handle keeps fingers and hands away from chain and sprockets. In addition, it has a charging system check that lets you know if your bike is charging properly. It features a 40 inch cord so you can see in those out of the way places when you need to. Quick release one-piece clamps that saves space. These are great for fuel lines, controlling wires, and can be used many times. Made from medium carbon steel with hardened jaws.

It features spanner pins and the jaws open up to 5" wide. It's ideal for holding clutch hubs, flywheels, gears, sprockets, etc. Made by Motion Pro. This tool is designed to separate vertically split crank case halves on two and four stroke engines.

Adjustable arms allow it to be used on multiple bolt patterns found on a variety of makes and models of motorcycles. Industrial grade steel construction with black oxide finish for long service life. Comes with 8mm mounting bolts and 6mm adapters. Protective carrying case included. A compact and lightweight solution to eliminate the SNAP for a safer tow. If you have ever towed a motorcycle you are familiar with the snap that comes with a traditional tow strap.

GCAG made the Dynatow with a section that gives 32 inches of stretch so both riders have an easier tow. The 26 foot total length gives you enough room to maneuver around obstacles and allows the freedom to choose better lines if you are towing in the gnar. You can also use this as a recovery strap. You can girth hitch the loop end to the bike and throw the other end to a friend to pull.

The dynamic properties of the Dynatow will help assist the pull. All of this functionality fits in a flat pouch about the size of sandwich and only weighs Throw it in your bag and be prepared. Please consider the following before use: Practice before you need to use this product. They recommend a proper training class to learn safe methods for towing a motorcycle.

Installing new turn signals or brake lights and need to find the 'HOT' wire, or are you just trying to find out if a specific wire has power going to it? Either way, this test light can help you locate shorts, open, and voltage on volt DC circuits. Having the proper fork oil level is imperative to the handling of your bike. Setting the correct fork oil level is a snap with this fully adjustable gauge.

The adjustable aluminum level plate can be set from 0 to mm. The oil reservoir has single milliliter markings up to 60ml. Being able to accurately tune your forks by adjusting the oil level can make them better resist brake dive or bottoming. Oil level should be thought of as a fine tuning method to make your choice of spring rate work perfectly for your bike.

Designed to check the amount of cylinder leakage in a 4-stroke engines. Gauge registers the total percentage of leakage past the rings, head gasket, intake and exhaust valves. This tester will speed up troubleshooting and will help to isolate bad components. The GCAG handles are comfortable to pull so whoever is helping will pull harder, and they are soft against your fender so you won't have any annoying bouncing, noise, or graphics damage.

GCAG dirt bike lift strap handles are constructed of 1" thin nylon webbing with flat stainless steel tri-glides for attachment. The grip section is built with 1" climb-spec tubular nylon webbing and a comfort grip handle.

Maintain your chain or sprocket, even change your rear tire or wheel while out on the road without the need for a center stand, with the BikeMaster Liftstick. Handy and convenient to carry.

Perfect for street, dual sport and trail use. Liftstick includes non-slip rubber boots, which protect your motorcycle's swingarm from any scratches while claws at the base provide traction and stability during use. Make your life a little easier by having a set of these in your toolbox. Designed to simplify installation and removal of clip-type master links. One tip is shorter and notched to be placed on the pin which allows the longer end to push the clip.

A high quality master link press tool from Wirth Machine used for the removal and installation of master links using a press fit link plate. Use this tool to check for air leaks in two-stroke engines. It includes air pressure gauge, pump-up bulb and most fittings and adapters for single and twin-cylinder two-stroke motorcycle engines.

Packed in a convenient carrying case with instructions. Showa removed the schrader valve on many newer rear shocks. Now you need a needle to recharge your shock with nitrogen after a rebuild. Race Tech built this unit just for that job. The features of this tool include psi capacity, bleeder valve and T-handle plunger pin chuck.

Swivel chuck has a 12" flexible hose. Comes complete with instructions, carrying box and Schrader valve extension required on some Showa shocks. Nitrogen bottles available at any welding supply house. Makes installation of your linkage bearings much easier. Also simplifies maintenance of those bearings. The Snapjack is an easy to use, portable, sturdy jack for chain lubricating, adjustment and chain drive maintenance. Also, simplifies cleaning. Includes front brake locking strap and handy carrying bag.

A professional level adjustable spoke torque wrench. Range from 0 to 62 inch pounds. The handle has a rubber coated end to protect your rims from scratches. Includes Torque wrench, standard handle for tough disassembly work and seven different size tips, all packed in a protective case. Recommended for use with Warp 9 wheels. Please measure nipple size to ensure proper fit.

The Phillips type screws used in Japanese motorcycles are actually Japanese Industrial Standard JIS screws are very easy to strip if you are using a regular Phillips screwdriver. There is bit in each end of the driver held in place magnetically. The narrow drive head profile easily fits into tight locations. Main shaft is 8. It seems that while packing for every adventure … we always end up with a few items that were either neglected to be packed, were last minute gear additions, or just needed to be packed in a readily accessible location….

Once packed the tool pouch can be slipped into any bag or attached externally using integrated webbing loops that are built into the pouch. A must for getting your wheels straight, concentric and true. For use with a truing and balancing stand. Always wanted to build or true your own wheels?

Maybe just be able to balance your wheels after changing tires. This stand is perfect for both of those tasks. Simplify self recovery with this quick deploy Z-Drag kit.

It can sap your energy trying to get your bike unstuck.



0コメント

  • 1000 / 1000